|
We offer a great range of Services to enhance our stone and granite workTops for Kitchens, bars, Bathrooms and a wide selection of Fireplaces etc
Granite Templates & Fitting Services
A templating and fitting service can be provided by us for your convenience. Dates for these would be arranged by us at the time of your order confirmation. A usual price for this service is £200 to £300 pounds payable to the fitter on completion of the installation. However as some projects would require more or less work than standard or may be located further away from our factory this cost may alter. Please be advised that we will notify you of the exact price when you confirm your order If you require this service.
Please read our granite & quartz Templating conditions by clicking here
Tiling Specialist Services
www.talktiles.co.uk
professional wall & floor tiler
ceramics, porcelain
And all natural products fitted
22 Years experience
Contact Mark Hamer 07976 721937
Joinery Services
Sorrento Joinery
All Aspects of Joinery Work Undertaken
18yrs Ex-Time Served Joiner
Hand Built Bespoke Kitchens Supplied & Fitted
Kitchen Installiation Only Service Available
Tel Angelo Palomba 07711805050
Gas Services
S.R.B Gas Services for Industrial,Commercial & Domestic
Servicing, Maintenance,Fault Finding & Installation,
Landlords Certificates
Ex British Gas 20+ yrs
Ex Gasforce
Steve Burton TEL 07970841963
Electrical services
John Hailwood Electrical Services for Industrial,Commercial & Domestic
Maintenance,Fault Finding,Installation
Landlords Certificates
NIC Approved Electrial Contractor
Free Qoutations & Advice
Contact John Hailwood TEL 07850721553
Fireplace Fitting Service
Gas-Safe Installiations
Limestone,Marble,Granite fireplaces fitted
All Styles Of Fireplaces Fitted
Corgi Registered Gas Fitter
Design Service Available
Gas Fires Supplied
Tel Mark 07980614818
><Templating Conditions
In order for us to process and manufacture projects as efficiently and accurately as possible, it is essential the following points are carried out prior to us templating on site
All surfaces/carcasses to be templated must be complete, flat and level. The final of the worktops can only be as good as the level of the units supporting them.
We accept no liability for problems caused additions or alterations to the furniture or appliances ect. after the templating has taken place.
If replacing existing worktops they must be removed .This allows the carcasses to be viewed and assessed and advice can then be given if any additional work needs
To be carried out before the new worktops could be fixed
Gas or electric hobs must be disconnected but available on site.
Belfast/butler sinks must be fixed in position before we can template.
Under mounted sinks must be on site at the template stage,If we are templating and fitting your worktops we will fit the undermounted sink at the fitting stage
Inset sinks and taps must be disconnected but available on site.
Any units to be fitted directly on top of the worktops must be fitted after the worktops (recommended) or on adjustable wall brackets to give adequate clearance. It is not acceptable to leave a gap and expect to slide the worktops under.
If any walls around the worktops are to be plastered or altered in any way they must be done either before templating or after fitting the worktops.
We would request that you or a trusted representative be present during templating to agree all relevant details such as overhang, joints and height of splash backs ect. Advice can also be given at this point with regard to any alterations and/or additional work that would need to be carried out before the new worktops can be fitted.
Unless specified, we reserve the right to use our own judgment regarding all overhangs but accept no responsibility if these are later found to be unacceptable.
Where templates are supplied to us by you they must be to actual finished size. All requirements must be clearly marked on the template including edges to be polished ,position of tap holes ,splash backs with correct polished edges ect. All joint positions must be clearly marked “GRANITE JOINT” (material constraints permitting).All internal cut-outs (hobs, sinks and hand wash basins ect) must be cut out accurately and separate templates from the manufacturer supplied. All templates must be numbered i.e. 1of7 2of7 ect.
If any of the above conditions are not met, we will use our best endeavors to template but take no responsibility whatsoever for any misinterpretations.
Fitting Conditions
If any sink, tap or hob has been reconnected after templating they must be disconnected and removed.
All electrical, gas and sink fittings to be removed by you or your kitchen fitting company if they interfere in any way with the installation of the new worktops.
Tiling in areas around the worktops must take place after fixing the worktops.
In the event of plasterwork ect. Being disturbed during fixing, all making good and subsequent cost to be the clients responsibility.
We have neither the tools nor the skills to undertake any plumbing, gas, electrical, plastering or carpentry work.
Standing on the finished worktops is to be avoided at all costs.
all work surface levels will follow unit levels
Upon compleation of fitting you or your representitive will be asked to sign a satisfaction note to say that you accept the workmanship and quality of your granite surface and that they meet your requirements.
  
Zircone Verde
Alger Verde
Luciente
Click any image above to view larger
sample
Click Here to
Order a Sample
When Ordering Samples please state the colour and
finish in the enquiry/comment section.
|
